Arduino nano/UNO対応の回路図である。スイッチ入力がアナログポートを使ったレベルによる入力判定を行っている。
ヘッダーファイル
si5351a.hは、スケッチと同じフォルダーに入れる事。Download siteにヘッダーファイル、スケッチ、vfo_v3_eepを保存した。////////////////////////////////////////////////////////////////////////
// Author: Hans Summers, 2015
// Website: http://www.hanssummers.com
//
// A very very simple Si5351a demonstration
// using the Si5351a module kit http://www.hanssummers.com/synth
// Please also refer to SiLabs AN619 which describes all the registers to use
//----------------------------------------------------------------------
// Addered: JA2GQP,2016/8/18
////////////////////////////////////////////////////////////////////////
#define I2C_START 0x08
#define I2C_START_RPT 0x10
#define I2C_SLA_W_ACK 0x18
#define I2C_SLA_R_ACK 0x40
#define I2C_DATA_ACK 0x28
#define I2C_WRITE 0b11000000
#define I2C_READ 0b11000001
#define SI_CLK0_CONTROL 16 // Register definitions
#define SI_CLK1_CONTROL 17
#define SI_CLK2_CONTROL 18
#define SI_SYNTH_PLL_A 26
#define SI_SYNTH_PLL_B 34
#define SI_SYNTH_MS_0 42
#define SI_SYNTH_MS_1 50
#define SI_SYNTH_MS_2 58
#define SI_PLL_RESET 177
#define SI_R_DIV_1 0b00000000 // R-division ratio definitions
#define SI_R_DIV_2 0b00010000
#define SI_R_DIV_4 0b00100000
#define SI_R_DIV_8 0b00110000
#define SI_R_DIV_16 0b01000000
#define SI_R_DIV_32 0b01010000
#define SI_R_DIV_64 0b01100000
#define SI_R_DIV_128 0b01110000
#define SI_CLK_SRC_PLL_A 0b00000000
#define SI_CLK_SRC_PLL_B 0b00100000
#define XTAL_FREQ 25000000 // Crystal frequency for Hans' board
uint8_t i2cStart(){
TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
while (!(TWCR & (1<<TWINT))) ;
return (TWSR & 0xF8);
}
void i2cStop(){
TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
while ((TWCR & (1<<TWSTO))) ;
}
uint8_t i2cByteSend(uint8_t data){
TWDR = data;
TWCR = (1<<TWINT) | (1<<TWEN);
while (!(TWCR & (1<<TWINT))) ;
return (TWSR & 0xF8);
}
uint8_t i2cByteRead(){
TWCR = (1<<TWINT) | (1<<TWEN);
while (!(TWCR & (1<<TWINT))) ;
return (TWDR);
}
uint8_t i2cSendRegister(uint8_t reg, uint8_t data){
uint8_t stts;
stts = i2cStart();
if (stts != I2C_START)
return 1;
stts = i2cByteSend(I2C_WRITE);
if (stts != I2C_SLA_W_ACK)
return 2;
stts = i2cByteSend(reg);
if (stts != I2C_DATA_ACK)
return 3;
stts = i2cByteSend(data);
if (stts != I2C_DATA_ACK)
return 4;
i2cStop();
return 0;
}
uint8_t i2cReadRegister(uint8_t reg, uint8_t *data){
uint8_t stts;
stts = i2cStart();
if (stts != I2C_START)
return 1;
stts = i2cByteSend(I2C_WRITE);
if (stts != I2C_SLA_W_ACK)
return 2;
stts = i2cByteSend(reg);
if (stts != I2C_DATA_ACK)
return 3;
stts = i2cStart();
if (stts != I2C_START_RPT)
return 4;
stts = i2cByteSend(I2C_READ);
if (stts != I2C_SLA_R_ACK)
return 5;
*data = i2cByteRead();
i2cStop();
return 0;
}
// Init TWI (I2C)
//
void i2cInit(){
TWBR = 92;
TWSR = 0;
TWDR = 0xFF;
//#ifdef ARDUINO_AVR_MEGA2560
// PRR0 = 0;
//#else
PRR = 0;
//#endif
}
////////////////////////////////////////////////////////////////////////
// Set up specified PLL with mult, num and denom
// mult is 15..90
// num is 0..1,048,575 (0xFFFFF)
// denom is 0..1,048,575 (0xFFFFF)
///////////////////////////////////////////////////////////////////////
void setupPLL(uint8_t pll, uint8_t mult, uint32_t num, uint32_t denom){
uint32_t P1; // PLL config register P1
uint32_t P2; // PLL config register P2
uint32_t P3; // PLL config register P3
P1 = (uint32_t)(128 * ((float)num / (float)denom));
P1 = (uint32_t)(128 * (uint32_t)(mult) + P1 - 512);
P2 = (uint32_t)(128 * ((float)num / (float)denom));
P2 = (uint32_t)(128 * num - denom * P2);
P3 = denom;
i2cSendRegister(pll + 0, (P3 & 0x0000FF00) >> 8);
i2cSendRegister(pll + 1, (P3 & 0x000000FF));
i2cSendRegister(pll + 2, (P1 & 0x00030000) >> 16);
i2cSendRegister(pll + 3, (P1 & 0x0000FF00) >> 8);
i2cSendRegister(pll + 4, (P1 & 0x000000FF));
i2cSendRegister(pll + 5, ((P3 & 0x000F0000) >> 12) | ((P2 & 0x000F0000) >> 16));
i2cSendRegister(pll + 6, (P2 & 0x0000FF00) >> 8);
i2cSendRegister(pll + 7, (P2 & 0x000000FF));
}
////////////////////////////////////////////////////////////////////////
// Set up MultiSynth with integer divider and R divider
// R divider is the bit value which is OR'ed onto the appropriate
// register, it is a #define in si5351a.h
////////////////////////////////////////////////////////////////////////
void setupMultisynth(uint8_t synth, uint32_t divider, uint8_t rDiv){
uint32_t P1; // Synth config register P1
uint32_t P2; // Synth config register P2
uint32_t P3; // Synth config register P3
P1 = 128 * divider - 512;
P2 = 0; // P2 = 0, P3 = 1 forces an integer value for the divider
P3 = 1;
i2cSendRegister(synth + 0, (P3 & 0x0000FF00) >> 8);
i2cSendRegister(synth + 1, (P3 & 0x000000FF));
i2cSendRegister(synth + 2, ((P1 & 0x00030000) >> 16) | rDiv);
i2cSendRegister(synth + 3, (P1 & 0x0000FF00) >> 8);
i2cSendRegister(synth + 4, (P1 & 0x000000FF));
i2cSendRegister(synth + 5, ((P3 & 0x000F0000) >> 12) | ((P2 & 0x000F0000) >> 16));
i2cSendRegister(synth + 6, (P2 & 0x0000FF00) >> 8);
i2cSendRegister(synth + 7, (P2 & 0x000000FF));
}
////////////////////////////////////////////////////////////////////////
// Switches off Si5351a output
// Example: si5351aOutputOff(SI_CLK0_CONTROL);
// will switch off output CLK0
////////////////////////////////////////////////////////////////////////
void si5351aOutputOff(uint8_t clk){
i2cSendRegister(clk, 0x80); // Refer to SiLabs AN619 to see
//bit values - 0x80 turns off the output stage
}
////////////////////////////////////////////////////////////////////////
// Set CLK0 output ON and to the specified frequency
// Frequency is in the range 1MHz to 150MHz
// Example: si5351aSetFrequency(10000000);
// will set output CLK0 to 10MHz
//
// This example sets up PLL A
// and MultiSynth 0
// and produces the output on CLK0
////////////////////////////////////////////////////////////////////////
void si5351aSetFrequency(uint32_t frequency){
uint32_t pllFreq;
uint32_t xtalFreq = XTAL_FREQ;
uint32_t l;
float f;
uint8_t mult;
uint32_t num;
uint32_t denom;
uint32_t divider;
divider = 900000000 / frequency; // Calculate the division ratio. 900,000,000 is the maximum internal
// PLL frequency: 900MHz
if (divider % 2) divider--; // Ensure an even integer
//division ratio
pllFreq = divider * frequency; // Calculate the pllFrequency:
//the divider * desired output frequency
mult = pllFreq / xtalFreq; // Determine the multiplier to
//get to the required pllFrequency
l = pllFreq % xtalFreq; // It has three parts:
f = l; // mult is an integer that must be in the range 15..90
f *= 1048575; // num and denom are the fractional parts, the numerator and denominator
f /= xtalFreq; // each is 20 bits (range 0..1048575)
num = f; // the actual multiplier is mult + num / denom
denom = 1048575; // For simplicity we set the denominator to the maximum 1048575
// Set up PLL A with the calculated multiplication ratio
setupPLL(SI_SYNTH_PLL_A, mult, num, denom);
// Set up MultiSynth divider 0, with the calculated divider.
// The final R division stage can divide by a power of two, from 1..128.
// reprented by constants SI_R_DIV1 to SI_R_DIV128 (see si5351a.h header file)
// If you want to output frequencies below 1MHz, you have to use the
// final R division stage
setupMultisynth(SI_SYNTH_MS_0, divider, SI_R_DIV_1);
// Reset the PLL. This causes a glitch in the output. For small changes to
// the parameters, you don't need to reset the PLL, and there is no glitch
// i2cSendRegister(SI_PLL_RESET, 0xA0); // 2016/10/23 JA2GQP
// Finally switch on the CLK0 output (0x4F)
// and set the MultiSynth0 input to be PLL A
i2cSendRegister(SI_CLK0_CONTROL, 0x4F | SI_CLK_SRC_PLL_A);
}
//////////////////////////////////////////////////////////////////////// << JA2GQP >>
// Power strength
// Example: SetPower(1);
// The setting range is from 1 to 4
////////////////////////////////////////////////////////////////////////
void SetPower(byte power){
switch(power){
case 1:
i2cSendRegister(SI_CLK0_CONTROL,76); // CLK0 drive strength = 2mA; power level ~ -10dB
break;
case 2:
i2cSendRegister(SI_CLK0_CONTROL,77); // CLK0 drive strength = 4mA; power level ~ -6dB
break;
case 3:
i2cSendRegister(SI_CLK0_CONTROL,78); // CLK0 drive strength = 6mA; power level ~ -3dB
break;
case 4:
i2cSendRegister(SI_CLK0_CONTROL,79); // CLK0 drive strength = 8mA; power level := 0dB
break;
default:
i2cSendRegister(SI_CLK0_CONTROL,76); // CLK0 drive strength = 2mA; power level ~ -10dB
break;
}
}
スケッチ
//----------------------------------------------------------------------------------// Multi Band DDS VFO Ver3.1
// JA2NKD 2016.10.19
// Aruduino IDE 1.6.12
// Arduino nano/UNO
//
// <Rotary.h> https://github.com/brianlow/Rotary
// <EF_AD9850.h> http://forum.arduino.cc/index.php?topic=77483.0
// "Ucglib.h" https://github.com/olikraus/ucglib
// "si5351a.h" https://sites.google.com/site/ja2gqp/
//---------------------------------------------------------------------------------
// si5351a transplant 2016/10/23 JA2GQP
// (si5351a.h is original hedder file.)
//---------------------------------------------------------------------------------
//---------- Library include ----------
#include "si5351a.h" // 2016/10/23 JA2GQP
#include <SPI.h>
#include <EEPROM.h>
#include <Rotary.h>
//#include <EF_AD9850.h> // 2016/10/23 JA2GQP
#include "Ucglib.h"
/*
* Hardware SPI Pins:
* Arduino nano sclk=13, data=11
*/
// I/O setting
const byte __CS=10;
const byte __DC=9;
const byte __RST=8;
const byte modeout1=7; // 2016/10/24 JA2GQP
const byte modeout2=12; //
const byte bandout1=4; //
const byte bandout2=5; //
const byte bandout3=6; //
const byte txsw=A3; //
const byte meterin=A0; //
const byte analogsw=A1; //
// EF_AD9850 AD9850(ddsclock,ddsfqup,ddsreset,ddsdata); // 2016/10/23 JA2GQP
Rotary r=Rotary(2,3);
Ucglib_ILI9341_18x240x320_HWSPI ucg(__DC, __CS, __RST);
//---------- Variable setting ----------
long romf[4];
long freq =7100000;
long freqmax=7200000;
long freqmin=7000000;
long freqold=0;
long freqrit=0;
String freqt=String(freq);
long ifshift = 0;
long ifshiftLSB =8998500; // VFO>frequency USB/LSB is turn over
long ifshiftUSB =9001500;
long ifshiftCW =8999200;
long ifshiftAM =9000000;
long txshiftLSB =8998500;
long txshiftUSB =9001500;
long txshiftCW =9000000;
long txshiftAM =9000000;
long ddsfreq = 0;
long ddsfreqb; // 2016/10/23 JA2GQP
char f100m,f10m,fmega,f100k,f10k,f1k,f100,f10,f1;
int ddsstep=2;
int rit=0;
int fstep=100;
int steprom=1;
int fmode=3;
int fmodeold=1;
int flagrit=0;
int fritold=0;
int flagmode=0;
int meterval1=0;
int tmeterval=0;
int romadd=0;
int analogdata=0;
int band=0;
int bandmax=8;
//---------- Initialization Program ----------------------
void setup() {
i2cInit(); // I2c initialaz 2016/10/23 JA2GQP
delay(100);
ucg.begin(UCG_FONT_MODE_TRANSPARENT);
//ucg.begin(UCG_FONT_MODE_SOLID);
ucg.clearScreen();
ucg.setRotate270();
pinMode (bandout1,OUTPUT);
pinMode (bandout2,OUTPUT);
pinMode (bandout3,OUTPUT);
pinMode(txsw,INPUT_PULLUP);
pinMode(modeout1,OUTPUT);
pinMode(modeout2,OUTPUT);
PCICR |=(1<<PCIE2);
PCMSK2 |=(1 << PCINT18) | (1 << PCINT19);
sei();
// AD9850.init(); // 2016/10/23 JA2GQP
// AD9850.reset(); // 2016/10/23 JA2GQP
band=EEPROM.read(0x01);
romadd=0x010+(band*0x10);
for (int i=0; i<3;i++){
romf[i]=eepread((romadd+4*i));
}
freq = romf[0];
freqmin = romf[1];
freqmax = romf[2];
fmode = EEPROM.read(romadd+12);
steprom = EEPROM.read(romadd+13);
if (steprom==1){fstep=10;}
if (steprom==2){fstep=100;}
if (steprom==3){fstep=1000;}
if (steprom==4){fstep=10000;}
banddataout();
screen01();
chlcd();
if (fmode==0){fmode=3;}
else{fmode=fmode-1;}
modeset();
steplcd();
freqt=String(freq);
freqlcd();
}
//---------- Main program ---------------------------------
void loop() {
analogdata=analogRead(analogsw);
// ucg.setPrintPos(12,157);
// ucg.setColor(255,255,255);
// ucg.print(analogdata);
if (analogdata<50){
setstep();
} else if (analogdata<300){
modeset();
} else if (analogdata<600){
setrit();
}else if (analogdata<750){
bandcall();
}else if (analogdata<980){
bandwrite();
}
if (digitalRead(txsw)==LOW){txset();}
if (flagrit==1){
if (freqrit == fritold){
meter();
}
if (freqrit!=fritold){
ddswrite();
ritlcd();
fritold=freqrit;
}
}
else{
if (freq == freqold){
meter();
}
ddswrite();
freqt=String(freq);
freqlcd();
freqold=freq;
}
}
//---------- Function DDS set --------------- 2016/10/23 JA2GQP
void Fnc_Dds(long frequency){
if(ddsfreq != ddsfreqb){
si5351aSetFrequency(frequency);
SetPower(1);
ddsfreqb = ddsfreq;
}
}
//---------- meter --------------------------
void meter(){
meterval1=analogRead(meterin);
meterval1=meterval1/50;
if (meterval1>15){meterval1=15;}
int sx1=sx1+(meterval1*17);
sx1=sx1+41;
int sx2=0;
sx2=sx2+(40+((15-meterval1)*17));
ucg.setFont(ucg_font_fub35_tr);
ucg.setColor(0,0,0);
ucg.drawBox(sx1,180,sx2,16);
ucg.setPrintPos(40,200);
for(int i=1;i<=meterval1;i++){
if (i<=9){
ucg.setColor(0,255,255);
ucg.print("-");
}
else{
ucg.setColor(255,0,0);
ucg.print("-");
}
}
}
//---------- Encoder Interrupt -----------------------
ISR(PCINT2_vect) {
if (flagrit==1){
unsigned char result = r.process();
if(result) {
if(result == DIR_CW){
freqrit=freqrit+fstep;
if (freqrit>=10000){
freqrit=10000;
}
}
else{
freqrit=freqrit-fstep;
if (freqrit<=-10000){
freqrit=-10000;
}
}
}
}
else{
unsigned char result = r.process();
if(result) {
if(result == DIR_CW){
freq=freq+fstep;
if (freq>=freqmax){freq=freqmax;}
}
else{
freq=freq-fstep;
if (freq<=freqmin){freq=freqmin;}
}
}
}
}
//------------ On Air -----------------------------
void txset(){
noInterrupts();
if (fmode==0){ddsfreq=freq+txshiftLSB;}
if (fmode==1){ddsfreq=freq+txshiftUSB;}
if (fmode==2){ddsfreq=freq+txshiftCW;}
if (fmode==3){ddsfreq=freq+txshiftAM;}
// AD9850.wr_serial(0x00,ddsfreq); // 2016/10/23 JA2GQP
Fnc_Dds(ddsfreq); // DDS out 2016/10/24 JA2GQP
ucg.setPrintPos(110,140);
ucg.setFont(ucg_font_fub17_tr);
ucg.setColor(255,0,0);
ucg.print("ON AIR");
while(digitalRead(txsw) == LOW){
meter();
}
ucg.setFont(ucg_font_fub17_tr);
ucg.setColor(0,0,0);
ucg.drawBox(100,120,250,30); //45
ddswrite();
interrupts();
}
//------------- Mode change(LSB-USB-CW-AM) ------------
void modeset(){
ucg.setFont(ucg_font_fub17_tr);
ucg.setPrintPos(82,82);
ucg.setColor(0,0,0);
ucg.print("USB");
ucg.setPrintPos(12,82);
ucg.print("LSB");
ucg.setPrintPos(82,112);
ucg.print("A M");
ucg.setPrintPos(12,112);
ucg.print("C W");
if (fmode==0){
ifshift=ifshiftUSB;
ucg.setColor(255,255,0);
ucg.setPrintPos(82,82);
ucg.print("USB");
digitalWrite(modeout1,HIGH);
digitalWrite(modeout2,LOW);
}
if(fmode==1){
ifshift=ifshiftCW;
ucg.setPrintPos(12,112);
ucg.setColor(255,255,0);
ucg.print("C W");
digitalWrite(modeout1,LOW);
digitalWrite(modeout2,HIGH);
}
if (fmode==2){
ifshift=ifshiftAM;
ucg.setPrintPos(82,112);
ucg.setColor(255,255,0);
ucg.print("A M");
digitalWrite(modeout1,HIGH);
digitalWrite(modeout2,HIGH);
}
if (fmode==3){
ifshift=ifshiftLSB;
ucg.setPrintPos(12,82);
ucg.setColor(255,255,0);
ucg.print("LSB");
digitalWrite(modeout1,LOW);
digitalWrite(modeout2,LOW);
}
fmode=fmode+1;
if (fmode==4){fmode=0;}
ddswrite();
while(analogRead(analogsw) <1000);
}
//------------ Rit SET ------------------------------
void setrit(){
if(flagrit==0){
flagrit=1;
ucg.setFont(ucg_font_fub11_tr);
ucg.setPrintPos(190,110);
ucg.setColor(255,0,0);
ucg.print("RIT");
ritlcd();
}
else {
flagrit=0;
ddsfreq=freq+ifshift;
// AD9850.wr_serial(0x00,ddsfreq); // 2016/10/23 JA2GQP
Fnc_Dds(ddsfreq); // DDS Out 2016/10/23 JA2GQP
freqt=String(freq);
ucg.setFont(ucg_font_fub11_tr);
ucg.setPrintPos(190,110);
ucg.setColor(255,255,255);
ucg.print("RIT");
ucg.setColor(0,0,0);
ucg.drawRBox(222,92,91,21,3);
freqrit=0;
}
while(analogRead(analogsw) <1000);
}
//----------- Rit screen ----------------------
void ritlcd(){
noInterrupts();
ucg.setColor(0,0,0);
ucg.drawBox(222,92,91,21);
ucg.setFont(ucg_font_fub17_tr);
ucg.setColor(255,255,255);
ucg.setPrintPos(230,110);
ucg.print(freqrit);
interrupts();
}
//-------------- encorder frequency step set -----------
void setstep(){
noInterrupts();
if (fstep==10000){
fstep=10;
}
else{
fstep=fstep * 10;
}
steplcd();
while(analogRead(analogsw) < 1000);
interrupts();
}
//------------- Step Screen ---------------------------
void steplcd(){
ucg.setColor(0,0,0);
ucg.drawRBox(221,61,93,23,3);
ucg.setFont(ucg_font_fub17_tr);
ucg.setColor(255,255,255);
ucg.setPrintPos(220,80);
if (fstep==10){ucg.print(" 10Hz");}
if (fstep==100){ucg.print(" 100Hz");}
if (fstep==1000){ucg.print(" 1KHz");}
if (fstep==10000){ucg.print(" 10KHz");}
}
//----------- Main frequency screen -------------------
void freqlcd(){
ucg.setFont(ucg_font_fub35_tn);
int mojisuu=(freqt.length());
if(freq<100){
ucg.setColor(0,0,0);
ucg.drawBox(217,9,28,36);
}
if(f10 !=(freqt.charAt(mojisuu-2))){
ucg.setColor(0,0,0);
ucg.drawBox(245,9,28,36);
ucg.setPrintPos(245,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-2));
f10 = (freqt.charAt(mojisuu-2));
}
/*
if(freq<10){
ucg.setColor(0,0,0);
ucg.drawBox(245,9,28,36);
}
if(f1 !=(freqt.charAt(mojisuu-1))){
ucg.setColor(0,0,0);
ucg.drawBox(273,9,28,36);
ucg.setPrintPos(273,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-1));
f1 = (freqt.charAt(mojisuu-1));
}
*/
if(freq<1000){
ucg.setColor(0,0,0);
ucg.drawBox(202,9,15,36);
}
if(f100 !=(freqt.charAt(mojisuu-3))){
ucg.setColor(0,0,0);
ucg.drawBox(217,9,28,36);
ucg.setPrintPos(217,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-3));
f100 = (freqt.charAt(mojisuu-3));
}
if(freq>=1000){
ucg.setPrintPos(202,45);
ucg.setColor(0,255,0);
ucg.print(".");
}
if(freq<10000){
ucg.setColor(0,0,0);
ucg.drawBox(146,9,28,36);
}
if(f1k !=(freqt.charAt(mojisuu-4))){
ucg.setColor(0,0,0);
ucg.drawBox(174,9,28,36);
ucg.setPrintPos(174,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-4));
f1k = (freqt.charAt(mojisuu-4));
}
if(freq<100000){
ucg.setColor(0,0,0);
ucg.drawBox(118,9,28,36);
}
if(f10k !=(freqt.charAt(mojisuu-5))){
ucg.setColor(0,0,0);
ucg.drawBox(146,9,28,36);
ucg.setPrintPos(146,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-5));
f10k = (freqt.charAt(mojisuu-5));
}
if(freq<1000000){
ucg.setColor(0,0,0);
ucg.drawBox(103,9,15,36);
}
if(f100k !=(freqt.charAt(mojisuu-6))){
ucg.setColor(0,0,0);
ucg.drawBox(118,9,28,36);
ucg.setPrintPos(118,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-6));
f100k = (freqt.charAt(mojisuu-6));
}
if(freq>=1000000){
ucg.setPrintPos(103,45);
ucg.setColor(0,255,0);
ucg.print(".");
}
if(freq<10000000){
ucg.setColor(0,0,0);
ucg.drawBox(47,9,28,36);
}
if(fmega !=(freqt.charAt(mojisuu-7))){
ucg.setColor(0,0,0);
ucg.drawBox(75,9,28,36);
ucg .setPrintPos(75,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-7));
fmega = (freqt.charAt(mojisuu-7));
}
if(freq<100000000){
ucg.setColor(0,0,0);
ucg.drawBox(19,9,28,36);
}
if (f10m !=(freqt.charAt(mojisuu-8))){
ucg.setColor(0,0,0);
ucg.drawBox(47,9,28,36);
ucg .setPrintPos(47,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(mojisuu-8));
f10m = (freqt.charAt(mojisuu-8));
}
/*
ucg.setPrintPos(19,45);
if(freq>=100000000){
if(f100m !=(freqt.charAt(0))){
ucg.setColor(0,0,0);
ucg.drawBox(19,9,28,36);
ucg .setPrintPos(19,45);
ucg.setColor(0,255,0);
ucg.print(freqt.charAt(0));
f100m = (freqt.charAt(0));
}
}
*/
}
//----------- Basic Screen -------------------------
void screen01(){
ucg.setColor(255,255,255);
ucg.drawRFrame(1,1,314,55,5);
ucg.drawRFrame(2,2,312,53,5);
ucg.setColor(50,50,50);
ucg.drawRBox(5,60,60,25,3);
ucg.drawRBox(75,60,60,25,3);
ucg.drawRBox(5,90,60,25,3);
ucg.drawRBox(75,90,60,25,3);
ucg.setFont(ucg_font_fub17_tr);
ucg.setPrintPos(12,82);
ucg.setColor(0,0,0);
ucg.print("LSB");
ucg.setPrintPos(82,82);
ucg.print("USB");
ucg.setPrintPos(12,112);
ucg.print("C W");
ucg.setPrintPos(82,112);
ucg.print("A M");
ucg.setColor(255,255,255);
ucg.drawRFrame(220,60,95,25,3);
ucg.drawRFrame(220,90,95,25,3);
ucg.setFont(ucg_font_fub11_tr);
ucg.setColor(255,255,255);
ucg.setPrintPos(175,80);
ucg.print("STEP");
ucg.setPrintPos(190,110);
ucg.setColor(255,255,255);
ucg.print("RIT");
ucg.setColor(100,100,100);
ucg.setPrintPos(10,210);
ucg.print(" S: 1-----3-------6-------9---Over--------");
ucg.setPrintPos(10,177);
ucg.print(" P: 1-----3-----5-----------10--------------");
ucg.setPrintPos(10,230);
ucg.setColor(235,0,200);
ucg.print(" Home Blew DDS-VFO Ver3.1 JA2NKD");
ucg.setFont(ucg_font_fub35_tr);
ucg.setColor(0,255,0);
// ucg.setPrintPos(19,45);
// ucg.print("4");
// ucg.setPrintPos(47,45);
// ucg.print("3");
// ucg.setPrintPos(75,45);
// ucg.print("7");
// ucg.setPrintPos(103,45);
// ucg.print(".");
ucg.setPrintPos(273,45);
ucg.print("0");
}
//---------- DDS Frequency write -----------
void ddswrite(){
if (flagrit==0){
ddsfreq=freq+ifshift;
// AD9850.wr_serial(0x00,ddsfreq); // 2016/10/23 JA2GQP
Fnc_Dds(ddsfreq); // DDS out 2016/10/24 JA2GQP
}
if(flagrit==1){
ddsfreq=freq+ifshift+freqrit;
// AD9850.wr_serial(0x00,ddsfreq); // 2016/10/23 JA2GQP
Fnc_Dds(ddsfreq); // DDS out 2016/10/24 JA2GQP
}
}
//---------- Band data call from eeprom ----------
void bandcall(){
band=band+1;
if (band>(bandmax-1)){band=0;}
romadd=0x010+(band*0x010);
for (int i=0; i<3;i++){
romf[i]=eepread((romadd+4*i));
}
freq = romf[0];
freqmin = romf[1];
freqmax = romf[2];
fmode = EEPROM.read(romadd+12);
steprom = EEPROM.read(romadd+13);
if (fmode >=1 ){
fmode=fmode-1;
}else if (fmode==0){
fmode=3;
}
if (steprom==1){fstep=10;}
if (steprom==2){fstep=100;}
if (steprom==3){fstep=1000;}
if (steprom==4){fstep=10000;}
modeset();
steplcd();
freqt=String(freq);
freqlcd();
banddataout();
chlcd();
}
//---------- Band data write to eeprom ----------
void bandwrite(){
romadd=0x010+(band*0x010);
// for (int i=0;i<3;i++){
eepwrite(freq,romadd);
// }
EEPROM.write(0x001,band);
EEPROM.write(romadd+12,fmode);
if (fstep==10){steprom=1;}
if (fstep==100){steprom=2;}
if (fstep==1000){steprom=3;}
if (fstep==10000){steprom=4;}
EEPROM.write(romadd+13,steprom);
ucg.setPrintPos(110,140);
ucg.setFont(ucg_font_fub17_tr);
ucg.setColor(255,0,0);
ucg.print("Complete!!");
delay (500);
ucg.setColor(0,0,0);
ucg.drawBox(100,120,250,30);
//ucg.drawBox(41,145,270,16);
}
//---------- EEPROM Write(4byte) subroutine ----------
void eepwrite(unsigned long f0,int epadd){
for (int i=0; i<=3;i++){
EEPROM.write(epadd+i,f0%256);
f0=f0/256;
}
}
//---------- EEPROM Read(4byte) subroutin ----------
unsigned long eepread(int epadd){
unsigned long f0=0;
for (int i=3; i >=0 ;i--){
f0=f0*256+EEPROM.read(epadd+i);
}
return f0;
}
//---------- Band data output I/O ----------
void banddataout(){
digitalWrite(bandout1,LOW);
digitalWrite(bandout2,LOW);
digitalWrite(bandout3,LOW);
if (band==0){}
if (band==1){
digitalWrite( bandout1,HIGH);
}
if (band==2){
digitalWrite(bandout2,HIGH);
}
if (band==3){
digitalWrite(bandout1,HIGH);
digitalWrite(bandout2,HIGH);
}
if (band==4){
digitalWrite(bandout3,HIGH);
}
if (band==5){
digitalWrite(bandout1,HIGH);
digitalWrite(bandout3,HIGH);
}
if (band==6){
digitalWrite(bandout2,HIGH);
digitalWrite(bandout3,HIGH);
}
if (band==7){
digitalWrite(bandout1,HIGH);
digitalWrite(bandout2,HIGH);
digitalWrite(bandout3,HIGH);
}
}
//---------- Band No.(Chanel No.) write to LCD ----------
void chlcd(){
ucg.setColor(0,0,0);
ucg.drawBox(5,120,80,20);
ucg.setFont(ucg_font_fub11_tr);
ucg.setPrintPos(12,137);
ucg.setColor(255,255,255);
ucg.print("CH: ");
ucg.print(band+1);
}
